Integrated outdoor solar power system 3KW/5KW 2.56KWH
■ The whole system integration includes an off-grid solar inverter module, lithium iron phosphate
battery pack, PDU, and outdoor cabinet.
■ The system is commonly used in the corner of the city, remote roads, mountains, bad environments,
dust, moisture, rain, mist-erosion, very poor power qual ity in the area.
■ The system provides a continuous pure sine wave AC power supply for outside communications/network
■ It adopts ful l-digital double closed-loop control, combined with advanced SPWM technology to output
pure sine waves.
■ Two output modes: mains electricity bypass and inverter output; uninterrupted power supply.
■ Four charging modes: PV Only, Mains Electricity Priority, PV Priority, and PV&Mains Electricity hybrid
■ Advanced MPPT technology with 99.9% efﬁciency.
■ Comes with an LCD display and 3 LED indicators that can clearly indicate the status and data.
■ Power saving mode, reduce no-load loss.
■ Intel l igent variable-speed fan to efﬁciently dissipate heat and extend system l ifespan.
■ It comes with double l ithium battery activation modes: mains and PV, and supports l ithium battery
■ All-round protection for solar panels includes overload and short circuit protection, under-voltage and
over-voltage protection, and reverse polarity protection.
■ With sun protection, heat insulation, roof venti lation.
■ With waterproof and the ﬁltration dust inlet.
■ The cabinet body is designed for the IP55 protection level. The cabinet front door shutters with
waterproof design, on the back of welding outdoor cabinet.
■ Modular design is easy to maintain.
■ System conﬁguration AC and DC lightning protection.
■ Wide input voltage, avoids frequent switching to battery power because of large power grid voltage,
reduce battery failure probabi l ity, adapt to the power environment in poor areas.
■ The environment which require higher IP level, we use heat exchanger to effectively reduce the
temperature of box inside and improve IP protection level .
|Output voltage waveform||Pure sine wave|
|Rated output power(W)||3000||3000||5000|
|Rated output voltage(Vac)||230||120||230|
|output frequency range||50Hz ± 0.3Hz / 60Hz ± 0.3Hz|
|Bypass circuit breaker||63A|
|Rated battery input voltage||48V(minimum starting voltage 44V)|
|Battery voltage range||48VDC|
|Operating temperature range||-15°C to 55°C|
|Storage temperature range||-25°C ~ 60°C|
|Communication interface||USB/RS485(WiFi/GPRS)/Dry Node Control|
|Battery type||Lithium Battery|
|Maximum charge current||0-60A||0-40A||0-60A|
|Charge voltage range||40-58Vdc||40-60Vdc||40-58Vdc|
|Overcharge protection||Alarm and turn off charging in 1 minute|
|Maximum PV open circuit voltage||145VDC|
|PV operating voltage range||60-145VDC|
|MPPT voltage range||60-115VDC|
|Battery voltage range||40-60VDC|
|Maximum output power||4200W|
|PV charge current range(settable)||0-80A|
|Lithium Battery Pack|
|Rated Capacity||50Ah||Nominal Voltage||48VDC/51.2VDC|
|Cell Resistance 1Khz||≤0.8mΩ||Charge Voltage||3.65V|
|Working environment temperature||Charge:0°~C55°C|
|Elevation||Less than 2000m|
|Cycle life||2500cycles≥80%, 25±2℃, 1C/1C, 80% DOD|
■ Long-term storage of the battery needs to be placed in a dry, clean, dark, and well-ventilated indoor
environment. The suitable storage temperature range is -20~35℃.
■ Batteries must be stored and transported in a state close to 50% SOC.
■ For long-term storage, the electricity needs to be cycled every 6 months.
■ When loading and unloading the battery during transportation, please be careful not to drop it,
do not stack it over 4 layers, or place it upside down, and ensure that the front is facing up.